Don´t hesitate to contact us: Via e-mail: Via telephone: +46 8 622 1300 For more detailed information please visit Disclaimer The information in this document is for illustrative purposes only. The standards define that the testing must be performed at , which is defined as between 10 and 35 °C 50 and 95 °F. Please be aware that if you change your cookie settings, we can no longer guarantee our website to function properly. Vis, goujons et tiges filetées de classes de qualité spécifiées. It defines properties for sizes M1. Nuts with specified proof load values — Fine pitch thread 7.
Special care should be taken before substituting grades to make sure that an acceptable substitute is being used. Depending upon the diameter of the fastener, 4037 will work as well. I have a customer who wants a 10mm bolt made which must be equivalant to a grade 10. Bolts, screws and studs with specified property classes. If you continue without changing your browser settings, we'll assume that you are happy to receive all cookies on the Ovako website. If it must meet property class 10.
Set screws and similar threaded fasteners not under tensile stresses 6. Who is this standard for? Although the methodologies and materials for producing jigs and fixtures have evolved beyond the conventional metal tooling of years past, their position as a manufacturing staple remains constant due to the benefits they offer. . The purchaser of an Ovako product has the responsibility to ascertain and control the applicability of the products before using them. A574, however, is a socket head cap screw standard, so studs and hex bolts are left out and do not have a direct equivalent.
It's easy to and it's free. This material requires customer approval. The standard was withdrawn in 2012. Therefore the same maximum diameters apply for 8. I just want to avoid creating issues for our procurement team by using the wrong spec? It is divided into five nonconsecutive parts: 1. Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread 2.
Nuts with specified proof load values — Coarse thread 5. The data and examples are only general recommendations and not a warranty or a guarantee. The chemical composition is essentially restricted such that cold-heading grades of alloy steels 4037, 4140, 1541, etc. The equivalents listed below should be only considered as rough equivalents. Continuous development may necessitate changes in technical data without notice. With either of these two the heat treat concerns are minimized. The suitability of a product for a specific application can be confirmed only by Ovako once given the actual conditions.
The limiting factor for maximum size is the amount of the martensite in the core of the material. As always, an engineer should be consulted before grade substitutions are made. Michael- B8 and B8M is 304 and 316, respectively. I have a small screw machine shop where I make spacers and bolts from 12l14 steel. So Im worry that 10. It also excludes , which are covered under part 5. Join your peers on the Internet's largest technical engineering professional community.
This standard only applies to short screws and bolts with a nominal diameter between 3 and 10 mm. However, you can change your cookie settings at any time. It defines mechanical properties for fasteners that range from M1. Part 1 does not specify properties for fasteners that have head geometries that reduce the of the fastener, such as and heads. These two additional standards are fasteners that have the same mechanical properties as their base property class i.
This standard is the origin for other standards that define properties for similar metric , such as and. Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm With exception to part 7, which defines test standards, the parts of this standard define properties for fasteners made of and. Jigs and fixtures offer manufacturers a reliable process for delivering accurate, high-quality outcomes, whether for a specific part or feature, or for consistency across multiples of parts. The diameter and pitch combinations must adhere to and and the thread tolerances must adhere to parts 1, 2, and 4. This document is only valid for Ovako material. This is a standard set by the standards organization , a voluntary standards development organization that sets technical standards for materials, products, systems, and services. The standards do not cover fasteners that would otherwise apply but require special properties, such as or.
Product grades A and B. Regards, Cory Please see for tips on how to make the best use of Eng-Tips Fora. Filetages à pas gros et filetages à pas fin Title in German Mechanische Eigenschaften von Verbindungselementen aus Kohlenstoffstahl und legiertem Stahl. Other material, covering the same international specifications, does not necessarily comply with the properties presented in this document. The properties are defined for M1. Fasteners is the term used when bolts, screws and studs are considered all together. Where material costs are an issue, Boron steels like 10B30 are increasing in usage Europe but be careful of the hardenability and heat treat practice.
What is this standard about? There are several other coating options; zinc, Geomet, or other various proprietary coatings that are alternatives to hot dip galvanizing. Fatigue performance and impact strength will be better with a cold headed part, so if this is a requirement for the application, beware. Portland Bolt is happy to help if you have specific questions or needs. For additional Heat Treatment Data, please visit the Heat Treatment Guide. Tread carefully and follow the advice of the other posters.