97 ford contour water pump replacement. 5 Ways to Change the Water Pump on a 2.0L, 4 Cylinder Ford Probe 1993 to 1997 2019-05-15

97 ford contour water pump replacement Rating: 7,1/10 1946 reviews

Ford Contour Water Pump

97 ford contour water pump replacement

You can get to it from inside the car. Except the water, of course. The oil from that failure got on the timing belt. Nearly all car components, when allowed to stay in their worn-out or impaired state, can cause further damage to associated or nearby automotive parts. Push the tensioner back and remove the belt. If you're in a garage, keep the door open. It needs to free any old gasket material or other contaminants.

Next

Ford Contour Water Pump

97 ford contour water pump replacement

Align the new gasket properly over the bolt holes on the water pump and put it all back on the engine. You now have the information, it is up to you to decide. Monitor the coolant level for a few minutes of idling and make sure that it stays full; add coolant as needed. According to the Service manual, the bolts should be tightened to 18Nm 13 ft lbs. If you find that your water pump has been damaged, you will be able to order a new one.

Next

Water Pumps for Ford Contour for sale

97 ford contour water pump replacement

Failing to properly maintain your cooling system can lead to both, so make sure you keep up on your scheduled maintenance. Avoid spills or leaving open containers or soaked paper towels or rags in accessible locations. The older models do have two flat belts not v-belts and the newer models probably have a single serpentine belt. For electric water pumps on some newer cars, the engine's computer will be checked for codes, and tests will be performed to determine the proper repair. This ensures longer bearing life and reliable performance. Two of those 10mm bolts are upon the cover with one about 3 times longer and it was covered up by that power steering hose and the one in the center is about 4 times longer than the ones around the edges.

Next

97 1997 Ford Contour Water Pump

97 ford contour water pump replacement

If the water pump is driven by the timing belt, it's customary to replace the pump any time the belt is replaced. What you most likely be getting is just the impeller. Remove the clamps on the short rubber hose between the forward metal pipe that runs under the fwd cyl, bank and the thermostat assembly; remove the short rubber hose. Install the Water pump belt. Keep your repair costs down by ordering your water pump replacement for Ford Contour from AutoZone. Diagram shows both halves of the timing covers, belt, a large thin washer behind the harmonic pulley is a guard for the crankshaft opening in the lower half timing cover, retaining bolt for the harmonic pulley. Performance Part offers a comprehensive line of Water Pumps for a range of applications.

Next

Where is the water pump located on a 1997 Ford Contour 2.5 V6?

97 ford contour water pump replacement

Place a nice size 3gal tub under the car and loosen the coolant cap- left side, looking aft. Now that everything has been cleaned, it is time to reassemble. Locate the fuel injection rail on the top of the engine. Reconnect the negative terminal of the battery. Also, it would be a good idea to have a fire extinguisher handy, and a buddy standing by - just in case! What are the symptoms related to a bad water pump? Disconnect the battery ground cable. Outtro music snippet, by: joshwoodward. If the water pump fails 6 month later, guess what has to be taken off to replace the water pump? You may encounter issues or problems not covered in this article.

Next

Ford Contour Water Pump

97 ford contour water pump replacement

Remove the coolant expansion tank. Remove the accessory drive belt. When these are removed, the entire pump housing will be loose from the engine. Install the crankshaft pulley and torque the bolt to 115 Nm 85 lb-ft. Ford Contour Replacement Water Pump Information The radiator is designed to keep your Ford Contour's engine cool. If it not aligned properly then remove the belt, carefully realign all 3 marks and reinstall the belt, and double-check it again.

Next

ALLDATA

97 ford contour water pump replacement

Taking the pump off was a bit of a struggle since it didn't pop off that easy but I just worked with it and got it off. The timing belt and its tensioner and idler must be removed to install the new water pump and timing belt unless it is almost new; how and why is explained. I will make a small commission from Amazon if you purchase anything through the link. Replace short connector hose and clamps. Do it in a well-ventilated area. After all the miscellaneous reassembly is done, now install the motor mount bracket securely with its 3 bolts and 2 nuts onto the car fender and the motor mount itself with the long bolt and nut and 2 nuts that attach it to studs on the part of the bracket that is attached to the engine block. Remove the four 4 water pump bolts.

Next

Where is the fuel pump in a 97 Ford Contour?

97 ford contour water pump replacement

The tools needed will be mentioned in each step. There or two of these cam shafts. Give it some light taps with a plastic handled screwdriver to the side of the pump. In the end, I had to buy another pump - just the impeller half - and only replace that part. If I were working on your vehicle, I would suggest replacing the water pump while the timing belt is being serviced. Once the job is finished and you have verified that the pump is not leaking, reinstall the engine cover. RepairPal recommendations for water pump issues The entire cooling system, including coolant hoses and fittings, the radiator, the coolant fan and the fan clutch, should be inspected when replacing the water pump.

Next

Water Pump (Duratec)

97 ford contour water pump replacement

Ok, start by removing this from here Circled is the water pump and pulley. May 2013: More 2012 Vehicles Added including Fiat! Some will require significant disassembly of the front end of the motor — in these cases, you may be better off letting a handle the job. Or you could get them up from the ports if you find a way to use a piece of hose inserted snugly over each spark plug after each is unscrewed. Remove the water pump pulley. Move the pulley so that the belt slackens and remove the belt. All Replacement brand items are backed by 1-year, unlimited-mileage warranty.

Next