2004 mazda 6 2.3 timing marks. Timing marks on chain driven Mazda 6 2.3 2003? 2019-05-17

2004 mazda 6 2.3 timing marks Rating: 5,5/10 1973 reviews

Transferring parts from the old engine

2004 mazda 6 2.3 timing marks

I am kinda stuck with this engine now and am going to have to try to make it work. So no, it won't work. As stated here I switch over the front cover, valve cover, oil pressure sensor, oil pan, intake manifold. Also the 2005 coils aren't compatible with 2008 wires since they have different connectors. The fuzion engine also has the hole but its a little lower than the whole on the mazda engine.

Next

Mazda 3 Service Manual

2004 mazda 6 2.3 timing marks

Just retrace your steps and check every single connection again. Apply silicone sealant to the areas shown in the figure. Hook up the coolant hose to the thermostat housing. I removed the nuts and tried to gently pry it but it won't budge Andy ideas? First, can I use the intake that's on the fusion-only noticeable difference is where a vac line hooks in on my mazda intake, the fusions had a rubber plug covering the nipple, easily removeable will be using my throttle body from the mazda. I just finished another Fusion swap last night.

Next

MAZDA 3 engine timing reset

2004 mazda 6 2.3 timing marks

Sebastian, In order to help you, first I need to know exactly what you're trying to do. O K, checked fuel at rail. I found and downloaded a factory manual , which helped with torque settings and setting timing. Valve cover gasket actually it's a rubber ring , intake rubber rings and exhaust gasket reusable. Heres my tensioner gone bad on my freshly built motor!!!!! I tried to use it against the 07 crank pulley. I looked into having someone take of the valve cover and check timing but they where saying it would be hundreds of dollars to even look.

Next

Mazda 3 Service Manual

2004 mazda 6 2.3 timing marks

I found a cheap jdm engine but it has a coil pack instead of coil on boots. Crank pulley and sensor will have to be swapped. If someone just wants to make sure and eliminate the possibility of the cogs being out of alignment, there has to be a way to measure this. Apply silicone sealant to the engine front cover as shown in the figure. All of these things can cause a rich condition. The more I think about these engines, the more I hate them.

Next

Can You Show Me a Diagram of the Timing Marks for the 3.0 Engine

2004 mazda 6 2.3 timing marks

Did the ter down yesterday only toke about 4 hours. Also what do you mean i don't have to swap timing cover if what to swap pulleys? And thanks for all the help I really appreciate it! Swapped the cam, intake, timing chain cover, front pulley, oil pan, and sensors. My 03 Mazda 6 2. If what you're hearing is not lifter noise, it's probably just the injectors, which is normal. I did have a dealer mechanic have a quick look under the hood and he was certain that me having the older 2005 engine in the 2008 car would have unfix-able timing issues. Do you know what cam im suppose to have in the engine. Glad you got it figured out!! I do not know why the fusion parts did not work for him I just wanted to let you guys know.

Next

#456 Mazda 2.3L cam timing chain sync problem P0340

2004 mazda 6 2.3 timing marks

I was not able to get the fusion coils on there due to the harness being slightly different. The Mazda6 has several strong attributes, including responsive handling, excellent brakes, a reasonably spacious and comfortable interior -- and quick acceleration in the V6 version. He also checked for leaks on fuel rail and found none. Its messing with the trans, speedo and power steering. Post-Swap Notes After everything was swapped over I took the car out for a test drive and noticed that the engine wanted to stall when the car was stopped.

Next

Replacing timing chain 2004 Mazda 6 Chains L4

2004 mazda 6 2.3 timing marks

If you turn a little more to where the hole is back at the 6 o'clock position the cams are aligned and everything fits. Insert a wire with an approx. Tightening torque 1 75—104 N·m {7. I'm still n the garage and can't remember what else I needed to ask but that was def the most important question-thx If you are sticking with your Mazda throttle body then you should be able to use the Fusion intake manifold. You need use the 04 crank sensor and 04 crank pulley. You're welcome and I'm glad it worked out for you.

Next

MAZDA 3 engine timing reset

2004 mazda 6 2.3 timing marks

Geeze I am stumped and do not want to just put the newer cover on the older engine and possibly have no oil pressure or oil going to the tensioner etc. I know i have to change the intake cam,but i noticed that the intake cam sprockets are different as well. I later realized this wasn't the original 2008 engine when I saw that the dipstick was in the front of the engine as opposed to in the top like the second version which came with the 2008. I bought a 2004 Mazda6 2. I now need to go get the engine, I started disassembling first and have everything taken apart. Doing the timing chain repair separately is essentially repeating the labor.

Next

Can Anyone Tell Me How to Set the Timing on the 04 Mazda 3 2.3L

2004 mazda 6 2.3 timing marks

Other codes the motor threw were P0011 and P0012. One thing to watch out for when taking off the front end is that the ac lines have to be disconnect. Well I could and I have done it once installed a 2004 engine on a 2006 car , but a slight modification is required, I have to plug an oil hole in the front of the head; the engine ran well and had good oil pressure. Well just finished my swap of the 2006 Fusion motor in to my 2004 Mazda3 and it runs great! I have never done this for a Mazda before and wanted to know how to check or adjust the timing. Sebastian, it sounds like you need to read the guide again from the beginning and carefully follow it, step by step. Because the crank pulley and sensors are different the crank sensor mounts in different spots, which means you have to swap the front timing cover.

Next

Replacing timing chain

2004 mazda 6 2.3 timing marks

This version of the engine unlike the other older first versions of the engine has coil on plug as opposed to the the coil pack. This may be resolved by using the plastic valve cover from the '06, but I'm not going to bother with changing it. You will extend the life of the 2. Install in the reverse order of removal. Did you compare the thickness of the timing chains on the two engines, they should be different.

Next