That way you don't send voltage back into the radio or amp and risk damaging them. If you have the polarity reversed, the speaker cone will move backwards. If you are installing the new speakers in the front doors, you can mount the crossovers in each front kick panel or wire tie them up out of the way under the dash, on each side of the cab. If all of your fuses are good, your 1999 Dodge Ram may have a factory amplifier that needs to be turned on by your after market radio. Hey thanks a ton Jimmy! And also where would be the best place to tap into them at? See the description for more details on the video! It's nearly impossible to pass a wire through the molex connector at the door side of the boot.
The car stereo amplifier trigger wire has to be wired up to turn on your factory amplifier. I guess they do it that way so if you have to replace the door you can basically just plug in the wires from the new door to the connector to save time and labor. Best thing I can tell you is if you have sound with the ground cable connected to the factory radio, then twist the factory ground wire or cable together with the ground wire for the new Alpine deck, and connect them both to about a 14 gauge wire, run it down to the passenger's kick panel and ground it under an existing nut or bolt there. You are the brains of this site! Ground the new radio to clean solid metal under an existing bolt or nut in one of the kick panels. Then just connect the speaker output wires from the factory amp to the crossover for the new splits. And take a good look at the mating harness, be sure the amp remote wire on it connects to the right pin and wire on the radio harness. We wish to make a site valuable for many people.
Got sound to speakers and all. If there still is no sound, either the Pyle radio is bad or there is a problem with the amp. How to install car radio autoradio wiring harness stereo installation. It's actually better and more reliable to run your own new wires this way, but it's not completely necessary. Any help would be appreciated. At the bottom of this website there is additionally a 1999 Dodge Ram Radio Wiring Diagram image gallery, if the picture over is inadequate for you. Just use the harness that has only speaker wires on it and connect the speaker outputs from the radio to the speaker level inputs on the wire harness.
Our automotive wiring diagrams allow you to enjoy your new mobile electronics rather than spend countless hours trying to figure out which wires goes to which 1999 Dodge Durango part or component. Adding More Information If you would like to help the Modified Life community by adding any missing information or adding a new car audio wire diagram to our resource, please feel free to post it at the bottom of this page. Plus that one costs less. One of the most time consuming tasks with installing an after market car stereo, car radio, satellite radio, xm radio, car speakers, tweeters, car subwoofer, crossovers, audio equalizer, car amplifier, mobile amp, car amplifier, mp3 player, ipod or any car audio electronics is identifying the correct color car audio wires for your 1999 Dodge Durango. Free car radio wires stock diagram. The solid blue only has power on it when the radio is on.
How to install car radio wires. I have seen harnesses in the past where the wire skipped the right pin and therefore the amp would not turn on. And if I do need to use it, where do I put them in the wiring scheme? Check the speaker outputs on the Pyle radio by connecting a known working speaker to them. There is no ground wire in the radio wire harness for the radio, Dodge grounds the case of the radio to metal behind the dash. What was the problem anyway? The battery constant always sends power to the radio to save your radio stations and other audio settings. Find the free Dodge wiring diagram you need and get started repairing your Dodge electrical problems. Get 5% discount on all car audio items at www.
Really appreciate the help on this. Before you dive in with a , you will want to obtain a free wiring diagram for your specific model. The rubber is pretty hard and thick, when I did mine I actually drilled a hole in it. Touch one wire to the + post and the other wire to the - post on the battery and when you find 2 wires that go to a speaker, the speaker cone will move and make a popping noise. What you can do is cut a hole in the bottom side of the flat rubber grommet for the boot on the door side and run your new wires through the hole. Above answer is Bogus, site is strictly a referal site no wiring diagrams are on this site. The wiring diagram for a 2002 Dodge Durango can be located at www.
Appreciate your knowledge on this subject. Richard, you may have mixed up the battery constant and accessory switched wires. I know usually they would go to an amp if it was an after market amp. Do you know the color code for the wires under the dash that I would need to connect to the crossover? If you do it that way you don't connect any of the factory speaker wires in the doors to the new tweeters or mids. Wasn't until I tried putting the old deck back in like you suggested that I realized where it was going to.
Post back if there is anything else you need. And be sure the amp remote on wire in the harness connects to the correct amp remote on wire in the radio harness on the truck side, it is dark green with an orange or red stripe. On the door side of the boot, it is just a large thick rubber boot but on the truck door jamb side of that boot, there is a hard plastic molex connector connecting the wires from the door to the truck body. On most radios the amp remote on wire is blue with a white stripe. Automotive wiring in a 1999 Dodge Durango vehicles are becoming increasing more difficult to identify due to the installation of more advanced factory oem electronics. This is tough to do without a wiring diagram to help guide you through your diagnostic procedure.